Wago 787-602 Switched-mode power supply; Classic; 1-phase; 24 VDC output voltage; 1.3 A output current
Wago
$214.30
(No reviews yet)
Write a Review
Write a Review
Wago
Wago 787-602 Switched-mode power supply; Classic; 1-phase; 24 VDC output voltage; 1.3 A output current
EPSITRON power supply; single-phase; output voltage 24 VDC; 1.3 A
- conformity marking:
- CE
- connection technology:
- CAGE CLAMP
- connection type 1:
- Input/output
- control deviation:
- ¤ 3 %
- country of origin sales organisation germany:
- DE
- current limitation:
- 1.5 x Io nom (typ.)
- default setting:
- DC 24 V
- depth from upper edge of din rail:
- 90 mm / 3.543 inch
- derating:
- -3 %/K (> 50 C)
- discharge current:
- ¤ 0.9 mA
- efficiency typ:
- 0.83
- fine stranded conductor:
- 0.08 2.5 mm / 28 12 AWG
- fire load:
- 0.000 MJ
- height from upper edge of din rail:
- 95 mm / 3.74 inch
- input current ii:
- ¤ 0.3 A (230 VAC)
- input voltage range:
- AC 90 264 V: DC 130 300 V
- inrush current:
- ¤ 25 A
- internal fuse:
- T 2 A / 250 VAC
- isolation voltage pri gnd:
- DC 2.2 kV
- isolation voltage pri sec:
- DC 4.242 kV
- isolation voltage sec gnd:
- DC 0.7 kV
- mains failure hold up time:
- 20 ms (230 VAC)
- mounting type:
- DIN-35 rail
- nominal input voltage ui nom:
- 1 x AC 100 240 V: DC 140 300 V
- nominal mains frequency range:
- 50 60 Hz: 0 Hz
- nominal output current io nom:
- 1.3 A (24 VDC)
- nominal output voltage uo nom:
- DC 24 V (SELV)
- note conductor cross section:
- 12 AWG: THHN, THWN
- open circuit proof:
- Yes
- operation status indicator:
- Green LED (24 V OK)
- output voltage range:
- DC 22 28.8 V (adjustable)
- overload behavior:
- Hiccup
- overvoltage protection secondary:
- Internal protective circuit || ¤ 40 VDC (in the event of a fault)
- packaging type:
- Box
- parallel operation:
- No
- phases:
- 1
- pollution degree:
- 2
- power factor correction pfc:
- Passive
- power loss max pl max:
- 7 W (90 VAC / 24 VDC: 1.3 A)
- power loss pl:
- ¤ 4.9 W (230 VAC: No load)
- protection class:
- I
- protection type:
- IP20 (per EN 60529)
- recommended backup fusing:
- Circuit breaker: C10 or B10
- relative humidity:
- 30 85 % (no condensation permissible)
- required backup fusing:
- An external DC fuse is required for the DC input voltage.
- residual ripple:
- ¤ 100 mV (Peak-to-peak)
- resistance to reverse feed:
- ¤ DC 30 V
- series operation:
- Yes
- short circuit protected:
- Yes ("hiccup")
- solid conductor:
- 0.08 2.5 mm / 28 12 AWG
- standards specifications:
- EN 60950-1 || EN 61204-3 || UL 60950 || UL 508 || GL
- strip length:
- 8 9 mm / 0.31 0.35 inch
- surrounding air temperature operation:
- -10 70 C
- surrounding air temperature storage:
- -25 85 C
- transient suppression primary:
- Varistor
- wago connector:
- WAGO 231 Series
- weight:
- 300.000 g
- width:
- 40 mm / 1.575 inch
